YSoft SafeQ Terminal Professional Installation Guide

FCC Statements

§ 15.21 Information to user

The user's manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. In cases where the manual is provided only in a form other than paper, such as on a computer disk or over the Internet, the information required by this section may be included in the manual in that alternative form, provided the user can reasonably be expected to have the capability to access information in that form.

§ 15.105 Information to the user

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. The operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Complete the Before-You-Begin checklist

Before you begin installing the terminal, complete this checklist:

  1. If possible, register and acquire access to the Y Soft online help desk a day or two before you begin the installation.

  2. Obtain the Terminal Professional installation packages and a small Phillips screwdriver.

  3. Make sure YSoft SafeQ Server is installed and running.

    Property startTerminalProfessionalLegacyServer has to be enabled.

  4. Write down the terminal's serial number (located on the back of the terminal).

  5. Make sure the Smart cable is the correct cable for the MFD you are connecting the terminal to.

    Refer to the MFD/cable part number compatibility list that Y Soft provided you or go to Hardware Compatibility List (HCL) and check the list there.

  6. If the cable you have is not correct, find the correct cable before you proceed. The cable may be among other Y Soft packages at the location where you are installing the terminal.

  7. Obtain the following information:

    1. The YSoft SafeQ Server IP address

    2. Does the network support DHCP?

    3. If it does not support DHCP, obtain this additional information:

    4. Terminal IP address

    5. Netmask address

    6. Gateway IP address

    7. DNS server IP address

  8. Information about the MFD or printer:

    1. IP address

    2. Serial number

    3. Model number

Check package contents

Check to make sure you have the following items (included in several packages):

images/download/attachments/160481613/package_1.png

Main package:

  • Terminal Professional

  • Ethernet cable

  • Power supply adapter

The package also includes clear plastic cable wrap for the Ethernet cable.

images/wiki.ysoft.local/download/attachments/80693060/second_package.PNG

Accessory packages:

  • Smart cable

  • MFD Universal Mounting Kit (bracket, screws, washers)

The Smart cable for your MFD may be different from the one shown here.

Connect cables

Connect cables in the order shown in this diagram.

You must connect the Smart cable before you connect the Power Supply Adapter cable.

The printer has to be connected to the network directly or by a switch in the Terminal Professional.

  1. On the back of the terminal, remove the cover and expose the connectors.

    images/wiki.ysoft.local/download/attachments/21955544/removing_back_cover.png

  2. Connect the cables as shown here:

    images/download/attachments/160481613/connections_TP35.PNG

Replace the back cover of the terminal

  1. Replace the terminal’s cover and tighten the screw.

    images/wiki.ysoft.local/download/attachments/21955544/replacing_back_cover.png

Mount the terminal

Depending on the type of bracket included with the terminal, mount the bracket to the MFP, to the wall, or to a nearby object such as a desk or table.

  1. Remove the two screws from the back of the terminal.

    images/wiki.ysoft.local/download/attachments/21955544/removing_bracket_screws.png

  2. Attach the mounting bracket to the terminal.

    images/wiki.ysoft.local/download/attachments/21955544/attaching_bracket.png

  3. If you have not already done so, write down the terminal’s serial number (located on the back of the terminal).

  4. Use the screws and washers included with the mounting bracket to mount the bracket and terminal onto the MFP.

  5. Cover all cables with the clear plastic wrap (included in the plastic bag with the cable). Start the wrap about 4 or 5 inches (10 to 12 cm) from the back of the terminal.

    images/wiki.ysoft.local/download/attachments/21955544/done.png

Verify installation

Before you verify installation:

If a user (with an associated card or PIN) has not been created in YSoft SafeQ, create one now for testing purposes as follows:

  1. In the YSoft SafeQ management interface, add a new user named "test".

  2. Assign a card and a PIN to the test user (for example, PIN1111).

If the terminal does not include a card reader:

  1. On the terminal’s PIN entry screen, enter 1111 (or whatever PIN you assigned to the test user); then touch OK.

  2. Check to make sure the MFP panel unlocks (that is, the panel lights up and comes on).

If the terminal includes a card reader:

  1. Touch the PIN button to display the PIN entry screen.

  2. Enter 1111 (or whatever PIN you assigned to the test user); then touch OK.

  3. Check to make sure the MFP panel unlocks (that is, the panel lights up and comes on).

If the MFP unlocks and the user is authenticated, installation is now complete.